Category Banner

* Clear Coats

AquaGard™

AquaGard™
AquaGard™ is a clear, durable, anti-yellowing water-based acrylic coating used as a top coat to increase a finished look and durability of a work piece. When fully cured, it also provides good chemical resistance to the finished surface.

AquaGard™ is available in gloss, satin, and dull sheens. It can be applied by brush, low-nap roller or sprayer. Thin up to 20% with tap water when needed. Do not apply AquaGard™ in temperatures below 55 degrees F. Applying top coats at low temperatures reduces the ability of this product to dry properly and obtain a good film formation, thus reducing its durability.

Covers up to 400 sq ft per gallon

Available in Gloss, Satin, and Dull Also available by special order with UV protection

Sold in quarts and gallons.
Download The SDS Sheet
AquaThane™

AquaThane™
AquaThane™ is a clear, durable, anti-yellowing water-based polyurethane coating used as a top coat to increase a finished look and durability of a work piece. This top coat dries to a very durable, chemical and water resistant finish. AquaThane™ may be applied by brush, roller or sprayer and can be thinned up to 20% with tap water if needed. AquaThane™ can be polished and rubbed smooth with steel wool and compounds after drying for at least 72 hours. AquaThane™ also can be used as clear top coat on concrete for maximum durability on walked on surfaces. The concrete should first be coated with SetCoat® or AquaGard™ because of their abilities to deeply penetrate and bond to the concrete.

Do not apply AquaThane™ in temperatures below 55 degrees F. Applying top coats at low temperatures reduces the ability of this product to dry properly and obtain a good film formation, thus reducing its durability.

Covers Approximately 400 sq ft per gallon

Available in Gloss, Satin, and Dull.

Sold in quarts and gallons.
Download The SDS Sheet
C-500 Urethane™

C-500 Urethane™
C-500 Urethane™ is a commercial quality, water-based, non-yellowing clear top coat for maximum durability. C-500 Urethane™ is pre-catalyzed so there is no messy mixing or measuring required. This product bonds and seals so completely it can be used for decorative sink bowls, vanities, and kitchen countertops.

Do not apply C-500 Urethane™ in temperatures below 60 degrees F. Applying top coats at low temperatures reduces the ability of this product to dry properly and obtain a good film formation, thus reducing its durability.

Apply one coat of AquaGard™ or ColorSeal to the finish. When dry, apply a light, even coat of C-500 Urethane™. Let dry at least 12 hours before applying additional coats. Do not apply more than 3 coats of C-500™.

Available in Gloss, Satin, or Dull sheens in quart and gallon sizes.

Cannot be sold or used in SCAQMD

Download The SDS Sheet
SetCoat® Clear

SetCoat® Clear
SetCoat® Clear is a clear paint that works both as a clear sealing coat and as a clear finish coat for color glazing a decorative finishing. When applied over 100% acrylic latex wall paint, it seals the surface, turning ordinary paint into an extraordinary base for easy workability and open time for decorative glaze finishes.

SetCoat® Clear can be brushed, rolled or sprayed on. Do not exceed 20% water by volume for spray on application. Apply with a flocked foam or short nap roller. Let dry at least overnight before applying color glazing mixtures.

SetCoat® Clear may be used for both interior and exterior applications, is low in VOC content and is friendly to the environment. Clean up with soap and water.

Do not apply SetCoat® Clear in temperatures below 55 degrees F. Applying paints and top coats at low temperatures reduces the ability of this product to dry properly and obtain a good film formation, thus reducing its durability.

Covers up to 400 sq ft per gallon

Available in quart and gallon sizes.
Download The SDS Sheet
Varnish Plus™

Varnish Plus™
Varnish Plus™ is a durable,water based, pre-catalyzed conversion varnish in an easy to use spray or brush on formulation. Its clear finish promotes excellent flow-out and tough film formation. Varnish Plus™ meets or exceeds standards as set forth in the furniture, kitchen cabinet, and millwork association for USA.

Apply by roller, brush or sprayer. Can be thinned up to 20% with water for spray applications. Apply the second coat within 4 hours of the first coat or wait 48 hours for recoating. Covers up to 400 sq.ft. per gallon. Do not apply Varnish Plus™ in temperatures below 55 degrees F. Applying top coats at low temperatures reduces the ability of this product to dry properly and obtain a good film formation, thus reducing its durability.

Available in gloss, satin and dull sheens

Sold in quart and gallon sizes.
Download The SDS Sheet
Dead Flat Varnish

Dead Flat Varnish
Our water-based clear topcoat designed to offer a flat no-sheen appearance when dry. May be applied by careful brushing, roller and spray on applications. Will look milky when first applied, but dries to a clear and flat appearance. The perfect dead flat clear coat finish when no sheen finish is desired. May be thinned up to 20% with tap water for spray on applications. Easy clean up using soap and water.

Sold in quarts.
Download The SDS Sheet
ColorSeal™

ColorSeal™
ColorSeal™ is a clear, easy to use, anti-yellowing water-based top coat for color sensitive artwork. It has a low, non-aggressive chemical makeup designed not to pull, move or smear any of the under laying dry color as it is applied. ColorSeal™ also is an excellent barrier and finish coat over glazes. It seals the decorative finishes without damaging existing color work. If needed a tougher, more durable topcoat can be applied over ColorSeal™.

ColorSeal™ is available in gloss, satin, and dull sheens. It can be applied by brush, low-nap roller or sprayer. Thin up to 20% with tap water when needed. Do not apply ColorSeal™ in temperatures below 55 degrees F. Applying top coats at low temperatures reduces the ability of this product to dry properly and obtain a good film formation, thus reducing its durability.

Sold in quarts and gallons.
Download The SDS Sheet
Venetian Gem® Finish Coat

Venetian Gem® Finish Coat
Venetian Gem® Finish Coat is a full bodied, trowel-on finish coat. Its translucent qualities produce a clear satin finish coat and may be color tinted to provide a decorative multi-colored finish.

Do not apply Venetian Gem® Finish Coat in temperatures below 55 degrees F. Applying this product at low temperatures reduces the ability of this product to dry properly and obtain a good film formation, thus reducing its durability.

Dries to a translucent satin finish.

Available in gallons.
Download The SDS Sheet
Venetian Gem® Gloss Coat

Venetian Gem® Gloss Coat
Venetian Gem® Clear Gloss Coat is a clear, full bodied, trowel on coating. It dries to a durable, water resistant, high gloss finish.

Easily tinted and versatile, Venetian Gem® Clear Gloss Coat can be used to add a clear, polished-looking final coat to any number of finishes. Intriguing multi dimensional effects can be created by tinting the material different complementary colors and layering the product over Venetian Gem® resulting in increased depth, play of light and color.

Do not apply Venetian Gem® Clear Gloss Coat in temperatures below 55 degrees F. Applying top coats at low temperatures reduces the ability of this product to dry properly and obtain a good film formation, thus reducing its durability.

Available in gallon sizes.
Download The SDS Sheet
Aqua Finishing Paste™

Aqua Finishing Paste™
Aqua Finishing Paste™ is a wipe-on, water-based co-polymer acrylic finish that has good wear and chemical resistance. Containing high-grade proprietary resins, it offers durability and superior bonding. As a clear, furniture-quality topcoat and decorative finishing material, this product allows for easy finishing on hard-to-finish surfaces, such as carved wood, chairs, ornate moldings, and railings. Aqua Finishing Paste™ has good wear and chemical resistance and can be polished and rubbed smooth with the of nylon pads after it has dried for at least 72 hours.

Aqua Finishing Paste™ is an excellent stenciling material because it can be tinted with FauxCreme Color and does not easily seep beneath the stencil edges—it also can be used to create embossed designs for decorative finishing.

Do not apply Aqua Finishing Paste™ in temperatures below 55 degrees F. Applying top coats at low temperatures reduces the ability of this product to dry properly and obtain a good film formation, thus reducing its durability.

Covers Approximately 50 - 200 sq ft per gallon

Sold in quarts.
Download The SDS Sheet